Note
Go to the end to download the full example code
静态循环分析#
在 1000 RPM 转速下，使用英制单位系统对转子扇形示例进行静态循环分析。
from ansys.mapdl.reader import examples
from ansys.mapdl.core import launch_mapdl
# launch mapdl
mapdl = launch_mapdl()
Load in the mesh#
加载示例扇形并绘制。
mapdl.cdread("db", examples.sector_archive_file)
mapdl.eplot()
Make the rotor cyclic#
进入前处理程序，使网格循环。
mapdl.prep7()
mapdl.shpp("off")
mapdl.nummrg(label="NODE", toler=1e-3)
mapdl.cyclic()
USE EXISTING MODEL FOR CYCLIC SYMMETRY
******************************************************
****** COMPUTED QUANTITIES ***************************
******************************************************
* NUMBER OF SECTORS = 15 *
* SECTOR ANGLE = 24.000 *
* CYCLIC COORDINATE SYSTEM = 1 *
* EDGE COMPONENTS CONTAIN NODES *
* LOW EDGE COMPONENT = CYCLIC_M01L MATCHED *
* HIGH EDGE COMPONENT = CYCLIC_M01H *
* LOW EDGE COMPONENT = CYCLIC_M02L MATCHED *
* HIGH EDGE COMPONENT = CYCLIC_M02H *
******************************************************
Set material properties#
单位为英制单位，材料为（近似）结构钢。
mapdl.mp("NUXY", 1, 0.31)
mapdl.mp("DENS", 1, 4.1408e-04)
mapdl.mp("EX", 1, 16900000)
MATERIAL 1 EX = 0.1690000E+08
Apply boundary conditions#
以 1000 RPM 的转速循环旋转，并将转子限制在中心位置。
mapdl.omega(0, 0, 1000) # 1000 RPM
mapdl.csys(1) # enter the cyclic coordinate system
mapdl.nsel("S", "loc", "x", 0, 0.71) # radial between 0.69 - 0.71
mapdl.d("ALL", "ALL") # all DOF for those 8 nodes
mapdl.allsel()
mapdl.csys(0) # return to cartesian coordinate system
ACTIVE COORDINATE SYSTEM SET TO 0 (CARTESIAN)
Run a static analysis#
运行 MAPDL 求解器并打印求解结果。
mapdl.run("/SOLU")
mapdl.antype("STATIC")
output = mapdl.solve()
mapdl.finish()
print(output)
*** NOTE *** CP = 8.547 TIME= 00:30:19
The automatic domain decomposition logic has selected the MESH domain
decomposition method with 2 processes per solution.
*** WARNING *** CP = 8.547 TIME= 00:30:19
The cyclic sector model contains volume and area element types. Please
verify the auto detected LOW and HIGH nodal edge component pairs
(CYCLIC command) for cyclic symmetry solution.
*** NOTE *** CP = 8.547 TIME= 00:30:19
There is no title defined for this analysis.
*** WARNING *** CP = 8.547 TIME= 00:30:19
Element shape checking is currently inactive. Issue SHPP,ON or
SHPP,WARN to reactivate, if desired.
*** WARNING *** CP = 8.547 TIME= 00:30:19
SOLID185 wedges are recommended only in regions of relatively low
stress gradients.
*** NOTE *** CP = 8.547 TIME= 00:30:19
The model data was checked and warning messages were found.
Please review output or errors file (
C:\Users\ff\AppData\Local\Temp\ansys_fdcyykaruq\file0.err ) for these
warning messages.
GENERATE CYCLIC SYMMETRY CONSTRAINT EQUATIONS
NUMBER OF CONSTRAINT EQUATIONS GENERATED= 102
(USING THE MATCHED NODES ALGORITHM -- MAX NODE LOCATION ERROR NEAR ZERO)
***** MAPDL SOLVE COMMAND *****
*** SELECTION OF ELEMENT TECHNOLOGIES FOR APPLICABLE ELEMENTS ***
---GIVE SUGGESTIONS ONLY---
ELEMENT TYPE 2 IS SOLID185. IT IS ASSOCIATED WITH LINEAR MATERIALS ONLY
AND POISSON'S RATIO IS NOT GREATER THAN 0.49. KEYOPT(2)=3 IS SUGGESTED.
*** MAPDL - ENGINEERING ANALYSIS SYSTEM RELEASE 2023 R1 23.1 ***
Ansys Mechanical Enterprise
20120530 VERSION=WINDOWS x64 00:30:19 JAN 24, 2024 CP= 8.641
S O L U T I O N O P T I O N S
PROBLEM DIMENSIONALITY. . . . . . . . . . . . .3-D
CYCLIC SYMMETRY SECTOR ANGLE. . . . . . . . . . 24.000 DEGREES
DEGREES OF FREEDOM. . . . . . UX UY UZ
ANALYSIS TYPE . . . . . . . . . . . . . . . . .STATIC (STEADY-STATE)
GLOBALLY ASSEMBLED MATRIX . . . . . . . . . . .SYMMETRIC
*** NOTE *** CP = 8.641 TIME= 00:30:19
Present time 0 is less than or equal to the previous time. Time will
default to 1.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 31.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 31.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 31.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 33.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 33.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 33.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 35.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 35.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 35.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 37.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 37.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 37.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 58.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 58.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 58.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 59.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 59.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 59.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 60.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 60.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 60.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 67.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 67.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 67.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 71.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 71.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 71.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 72.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 72.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 72.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 73.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 73.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 73.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 76.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 76.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 76.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 131.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 131.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 131.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 133.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 133.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 133.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 135.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 135.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 135.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 137.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 137.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 137.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 145.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 145.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 145.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 146.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 146.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 146.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 147.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 147.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 147.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 154.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 154.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 154.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 158.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 158.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 158.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 159.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 159.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 159.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 160.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 160.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 160.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 163.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 163.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 163.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 241.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 241.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 241.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 242.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 242.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 242.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 244.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 244.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 244.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 245.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 245.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 245.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 247.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 247.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 247.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 248.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 248.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 248.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 250.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 250.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 250.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 251.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 251.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 251.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 296.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 296.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 296.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 299.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 299.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 299.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 300.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 300.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 300.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 302.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 302.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 302.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 303.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 303.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 303.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 305.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 305.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 305.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 306.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 306.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 306.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 308.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 308.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 308.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 354.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 354.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 354.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 356.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 356.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 356.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 357.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 357.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 357.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 359.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 359.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 359.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 361.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 361.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 361.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 362.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 362.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 362.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 374.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 374.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 374.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 376.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 376.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 376.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 377.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 377.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 377.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 378.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 378.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 378.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 380.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 380.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 380.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 381.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 381.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 381.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 709.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 709.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 709.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 711.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 711.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 711.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 713.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 713.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 713.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 715.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 715.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 715.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 736.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 736.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 736.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 737.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 737.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 737.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 738.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 738.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 738.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 745.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 745.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 745.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 749.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 749.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 749.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 750.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 750.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 750.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 751.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 751.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 751.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 754.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 754.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 754.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 809.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 809.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UZ at unused node 809.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UX at unused node 811.
*** WARNING *** CP = 8.641 TIME= 00:30:19
Specified degree of freedom constraint UY at unused node 811.
************************************************************************
The number of ERROR and WARNING messages exceeds 200.
Additional messages suppressed. See (
C:\Users\ff\AppData\Local\Temp\ansys_fdcyykaruq\file0.err ) for
suppressed messages.
************************************************************************
*** NOTE *** CP = 8.641 TIME= 00:30:19
The step data was checked and warning messages were found.
Please review output or errors file (
C:\Users\ff\AppData\Local\Temp\ansys_fdcyykaruq\file0.err ) for these
warning messages.
*** NOTE *** CP = 8.641 TIME= 00:30:19
The conditions for direct assembly have been met. No .emat or .erot
files will be produced.
D I S T R I B U T E D D O M A I N D E C O M P O S E R
...Number of elements: 105
...Number of nodes: 678
...Decompose to 2 CPU domains
...Element load balance ratio = 1.038
L O A D S T E P O P T I O N S
LOAD STEP NUMBER. . . . . . . . . . . . . . . . 1
CYCLIC SYMMETRY HARMONIC INDEX. . . . . . . . . 0
TIME AT END OF THE LOAD STEP. . . . . . . . . . 1.0000
NUMBER OF SUBSTEPS. . . . . . . . . . . . . . . 1
STEP CHANGE BOUNDARY CONDITIONS . . . . . . . . NO
INERTIA LOADS X Y Z
OMEGA. . . . . . . . . . . . 0.0000 0.0000 1000.0
PRINT OUTPUT CONTROLS . . . . . . . . . . . . .NO PRINTOUT
DATABASE OUTPUT CONTROLS. . . . . . . . . . . .ALL DATA WRITTEN
FOR THE LAST SUBSTEP
SOLUTION MONITORING INFO IS WRITTEN TO FILE= file.mntr
**** CENTER OF MASS, MASS, AND MASS MOMENTS OF INERTIA ****
CALCULATIONS ASSUME ELEMENT MASS AT ELEMENT CENTROID
TOTAL MASS = 0.56778E-04
MOM. OF INERTIA MOM. OF INERTIA
CENTER OF MASS ABOUT ORIGIN ABOUT CENTER OF MASS
XC = -0.46671 IXX = 0.7738E-04 IXX = 0.5872E-05
YC = -1.0376 IYY = 0.2744E-04 IYY = 0.4694E-05
ZC = -0.42760 IZZ = 0.8087E-04 IZZ = 0.7379E-05
IXY = -0.2923E-04 IXY = -0.1734E-05
IYZ = -0.2474E-04 IYZ = 0.4481E-06
IZX = -0.1290E-04 IZX = -0.1567E-05
*** MASS SUMMARY BY ELEMENT TYPE ***
TYPE MASS
2 0.567777E-04
Range of element maximum matrix coefficients in global coordinates
Maximum = 3710503.22 at element 645.
Minimum = 117780.539 at element 587.
*** ELEMENT MATRIX FORMULATION TIMES
TYPE NUMBER ENAME TOTAL CP AVE CP
2 210 SOLID185 0.000 0.000000
Time at end of element matrix formulation CP = 8.671875.
DISTRIBUTED SPARSE MATRIX DIRECT SOLVER.
Number of equations = 1008, Maximum wavefront = 81
Process memory allocated for solver = 1.040 MB
Process memory required for in-core solution = 1.007 MB
Process memory required for out-of-core solution = 0.954 MB
Total memory allocated for solver = 1.943 MB
Total memory required for in-core solution = 1.875 MB
Total memory required for out-of-core solution = 1.696 MB
*** NOTE *** CP = 8.672 TIME= 00:30:19
The Distributed Sparse Matrix Solver is currently running in the
in-core memory mode. This memory mode uses the most amount of memory
in order to avoid using the hard drive as much as possible, which most
often results in the fastest solution time. This mode is recommended
if enough physical memory is present to accommodate all of the solver
data.
Distributed sparse solver maximum pivot= 4836504.28 at node 792 UX.
Distributed sparse solver minimum pivot= 49884.0902 at node 1081 UZ.
Distributed sparse solver minimum pivot in absolute value= 49884.0902
at node 1081 UZ.
*** ELEMENT RESULT CALCULATION TIMES
TYPE NUMBER ENAME TOTAL CP AVE CP
2 210 SOLID185 0.000 0.000000
*** NODAL LOAD CALCULATION TIMES
TYPE NUMBER ENAME TOTAL CP AVE CP
2 210 SOLID185 0.000 0.000000
*** LOAD STEP 1 SUBSTEP 1 COMPLETED. CUM ITER = 1
*** TIME = 1.00000 TIME INC = 1.00000 NEW TRIANG MATRIX
*** MAPDL BINARY FILE STATISTICS
BUFFER SIZE USED= 16384
0.312 MB WRITTEN ON ASSEMBLED MATRIX FILE: file0.full
0.438 MB WRITTEN ON RESULTS FILE: file0.rst
Plot the cyclic result#
使用传统方式（mapdl reader）打印结果
mapdl.result.plot_nodal_displacement(0)
Exit MAPDL#
Finally, exit MAPDL.
mapdl.exit()
Total running time of the script: (0 minutes 1.333 seconds)